PROFESSIONAL
POPCORN MAKER
g
n
i
r
r
a
W
POP
OFF
o
P
WPM25
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
16. Turn ALL switches to OFF position before
disconnecting power plug from the wall supply outlet.
17. Not recommended for outdoor use.
18. Do not use appliance for other than intended use.
19. To avoid overheating, always add oil and then kernels
before operating.
20. Extreme caution must be used when unloading
popcorn. Always place the unit over a countertop
so that residual hot oil or water running out will not
cause burns.
21. KEEP OUT OF REACH OF CHILDREN.
22. DO NOT CLEAN USING ANY ABRASIVE MATERIAL.
23. NEVER FORCE ANY PARTS OR BRACKETS INTO
POSITION.
24. CAUTION: A burn can result from misuse of this
product. Read popping instructions for proper
operating procedure.
25. No parts are intended for dishwasher.
26. A popper that is plugged into an outlet should not be
left unattended.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
POwER CORD INSTRUCTION
1. A short power-supply cord is provided to reduce the
risk resulting from becoming intangled in or tripping
over a longer cord.
2. Longer detachable power-supply cords or extension
cords are available and may be used if care is exer-
cised in their use.
3. If a long detachable power-supply cord or extension
cord is used:
a) The marked electrical rating of the extension cord
should be at least as great as the electrical rating
of the appliance.
ꢁ
b) If the appliance is of the grounded type, the extension
cord should be a grounding 3-wire cord.
c) The longer cord should be arranged so that it will not
drape over the countertop or tabletop where it can be
pulled on by children or tripped over unintentionally.
PARTS
g
n
i
r
a
W
3
POP
OFF
o
r
P
1
2
4
6
1. Housing
2. Kettle, Lid and Stirrer
3. Door (removable)
4. Tray (removable)
5. Light (not shown)
6. Measuring Spoon and Cup
ꢂ
ASSEMBLING PROCEDURE
g
g
in
POP
in
ar
W
ar
W
POP
OFF
OFF
ro
P
ro
P
FIGURE 2
Hook the kettle onto the
hanger of the main unit.
FIGURE 1
Place door on hinges.
g
in
ar
W
POP
OFF
ro
P
FIGURE 4
Finally, insert the internal
kettle plug into the socket
on the inner top of the
popcorn housing.
FIGURE 3
Insert tray.
ꢃ
POPPING INSTRUCTIONS
1. Follow assembly procedure.
2. Make sure the popcorn maker is unplugged before
you do any of the following.
3. Before using the unit, please check carefully to be sure
voltage (120V – 60 Hz ) is suitable to your home.
4. Clean the internal surface of the kettle with warm sudsy
water, rinse well and dry with a clean cloth. Wipe down
inner and outer housing with damp cloth.
5. Main unit has a 2-function switch as follows:
– POP to turn heater, stirrer and light on
– OFF to turn power off
6. Insert the internal plug into the socket (see figure 4,
previous page).
7. Plug the power cord into an electric outlet.
8. Before pouring oil or popcorn, lift lid up using the
lid tab. Turn the switch to the POP position. The
stirrer will begin to rotate in the kettle. Let the stainless
steel kettle preheat about 2 to 3 minutes. Add oil
(1 tablespoon of vegetable, corn, peanut, or safflower
oil). Immediately add 1/3 cup of corn kernels (Note:
1/3 measuring cup included) and close lid to the kettle.
Caution: Lid might be hot – it is recommended to
use an oven mitt.
9. Popcorn starts popping out through the lid after about
2 minutes. Yields up to 8 cups per batch in less than
3 minutes.
10. When unit is finished popping – you will no longer
hear the corn popping – immediately turn switch to the
Off position and rotate the knob of the kettle down to
release any remaining popcorn in the popper. This will
also stop the remaining popcorn from cooking any
further and avoid possible burning.
11. Keep POP switch off if the unit is not continuously
in use.
ꢄ
12. Remove plug from power supply if the unit is not
being used.
13. Repeat steps 8 to 10 for continuous popping.
CLEANING AND MAINTENANCE
It is strongly recommended to clean the kettle frequently to
avoid burning excess oil onto the bottom of the inner pot.
After using the popcorn machine, let it cool, and use a
wet cloth to clean the main unit, main body and door.
It is strongly recommended to wash and dry the tray after
each use to avoid any bacteria buildup. The light bulb is
replaceable with a 120 volt/10 watt bulb.
QUICK CLEANING PROCEDURE
Turn the POP control to Off. Pour 4 to 6 ounces of water
(NO detergent is necessary) into inner pot. Switch to POP
to boil the water and let the stirrer turn in order to remove
excess oil stuck on the surface. After cooling, pour out
the water into a deep bowl and discard after about 1 to 2
minutes of boiling. CAUTION: THE KETTLE IS HOT.
Or, remove the kettle and clean it with a Scotch-Brite®
scouring pad. Do not immerse kettle or electrical plug
in water.
ꢅ
Any other trademarks or service marks of third parties herein
are the trademarks or service marks of their respective owners.
©2008 Waring Products
Division of Conair Corporation
150 Milford Road
East Windsor, NJ 08520
Printed in China
WPM25 IB
08WR170
IB-8541
|